In the past (probably with 0.94 or 0.95) I have used wifi correctly with my dongle.
In the last month I have unable to use it anymore.
I have reflashed image and I have also purchased the Edimax Dongle.
Same result no WiFi with either dongles and with stable and beta images !!!
Stable image (0.96) with my older dongle:
Code: Select all
lsusb
Bus 001 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter
dmesg
[ 930.983438] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[ 931.011684] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 931.012256] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 931.071830] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 931.074264] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[ 931.479693] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Code: Select all
lsusb
Bus 001 Device 002: ID 7392:7811 Edimax Technology Co., Ltd EW-7811Un 802.11n Wireless Adapter [Realtek RTL8188CUS]
ip link
4: wlan0wext: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
dmesg
[ 1239.937626] rtl8192cu 1-1:1.0 wlan0wext: renamed from wlan0
[ 1240.594075] IPv6: ADDRCONF(NETDEV_UP): wlan0wext: link is not ready
Code: Select all
lsusb
Bus 001 Device 004: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter
ip link
6: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
dmesg
[ 210.777648] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[ 210.806531] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 210.807090] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 210.858988] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 210.864684] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[ 211.263871] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
uname -a
Linux rp-xxxxxx 4.4.0-xilinx #1 SMP PREEMPT Wed Nov 23 12:16:59 CET 2016 armv7l armv7l armv7l GNU/Linux
Code: Select all
lsusb
Bus 001 Device 002: ID 7392:7811 Edimax Technology Co., Ltd EW-7811Un 802.11n Wireless Adapter [Realtek RTL8188CUS]
ip link
4: wlan0wext: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
dmesg
[ 165.921648] rtl8192cu 1-1:1.0 wlan0wext: renamed from wlan0
[ 166.582781] IPv6: ADDRCONF(NETDEV_UP): wlan0wext: link is not ready
Code: Select all
lsusb
Bus 001 Device 002: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter
ip link
4: wlx000xxxxxxxxx: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
dmesg
[ 81.467867] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[ 81.496112] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 81.496697] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 81.539837] rt2800usb 1-1:1.0 wlx000xxxxxxxxx: renamed from wlan0
xxxxxxxxx = mac address
Code: Select all
lsusb
Bus 001 Device 003: ID 7392:7811 Edimax Technology Co., Ltd EW-7811Un 802.11n Wireless Adapter [Realtek RTL8188CUS]
ip link
5: enxxxxxxxxxxxxx: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
dmesg
[ 265.282625] rtl8192cu 1-1:1.0 enxxxxxxxxxxxxx: renamed from wlan0
xxxxxxxxxxxx = mac address