Slow Arbitrary Output with Matlab

Applications, development tools, FPGA, C, WEB
Post Reply
Posts: 2
Joined: Sun Jul 25, 2021 12:42 pm

Slow Arbitrary Output with Matlab

Post by ToBe » Mon Aug 30, 2021 3:24 pm

Hi Folks,

i'm trying to simulate an ECG signal by using SCPI and Matlab according to the official example ... -exm4.html. My raw ecg data is 10k points in total length and was sampled with 500 Sps. In my understanding, it should be fine to load the data in with the "SOUR1:TRAC:DATA:DATA" command and set the frequency to 500Hz for the Output.

Here is my Matlab Code:

Code: Select all

%% Define Red Pitaya as TCP/IP object
clear all
close all
IP= '';           % Input IP of your Red Pitaya...
port = 5000;
tcpipObj=tcpip(IP, port);

% Load File with raw ecg data
ecg_file = load('\raw_data\ecgiddb_pers26_1.mat', 'val');
ecg_data = ecg_file.val;
ecg_data_size = size(ecg_data,2);

% create TCP Object
tcpipObj.InputBufferSize = ecg_data_size*64;
tcpipObj.OutputBufferSize = ecg_data_size*64;

%% Open connection with your Red Pitaya and close previous
tcpipObj.Terminator = 'CR/LF';

% get biggest Signal Peak and normalize on it
ecg_peak = max(ecg_data);
ecg_data = ecg_data/max(ecg_data);

% Generating diff Signal
ecg_ch1 = ecg_data;
ecg_ch2 = ecg_data * (-1);      % inverting signal

%% Convert waveforms to string with 5 decimal places accuracy
waveform_ch_1_0 =num2str(ecg_ch1,'%1.5f,');
waveform_ch_2_0 =num2str(ecg_ch2,'%1.5f,');

waveform_ch_1 =waveform_ch_1_0(1,1:length(waveform_ch_1_0)-2);
waveform_ch_2 =waveform_ch_2_0(1,1:length(waveform_ch_2_0)-2);

fprintf(tcpipObj,'GEN:RST')                     % Reset to default settings

fprintf(tcpipObj,'SOUR1:FUNC ARBITRARY');       % Set function of output signal
fprintf(tcpipObj,'SOUR2:FUNC ARBITRARY');       % {sine, square, triangle, sawu, sawd}

fprintf(tcpipObj,['SOUR1:TRAC:DATA:DATA ' waveform_ch_1])  % Send waveforms to Red Pitya
fprintf(tcpipObj,['SOUR2:TRAC:DATA:DATA ' waveform_ch_2])

fprintf(tcpipObj,'SOUR1:VOLT 1');               % Set amplitude of output signal
fprintf(tcpipObj,'SOUR2:VOLT 1');

fprintf(tcpipObj,'SOUR1:FREQ:FIX 500');        % Set frequency of output signal
fprintf(tcpipObj,'SOUR2:FREQ:FIX 500');

fprintf(tcpipObj,'OUTPUT1:STATE ON');
fprintf(tcpipObj,'OUTPUT2:STATE ON');


The signal is generated fine, but with an incredibly high frequency.
Interestingly, when looking at the Signal with an oscilloscope, i can clearly see the "stair-ish" signal steps coming from the output of the RP. Measuring the time fo each of this steps results in a sampling rate of 8.3 MHz. When turning the frequency down to "1" I still measure around 16kHz.

So where is the problem here? Does the "SOUR1:FREQ:FIX 1" really sets the sampling rate in Hz, or is it the repitition rate of the Data-Block given by the :DATA command? Even then, it's totaly off (42 Hz vs. 1 Hz).
Also: when looking at the generated Signal, the signal has an awefull high jitter (~ 5ms with 1 Hz FREQ) - meaning that the characteristical peak in the ECG signal varies by 5ms between the periods. That also seems to be quiet bad...
I also power cycled the RP,.. no difference.

Thank you and kind regards

Post Reply
jadalnie klasyczne ekskluzywne meble wypoczynkowe do salonu ekskluzywne meble tapicerowane ekskluzywne meble do sypialni ekskluzywne meble włoskie

Who is online

Users browsing this forum: Bing [Bot] and 5 guests