122-16 and GnuRadio 3.10x

Just about everything about Red Pitaya
Post Reply
math_pitaya
Posts: 3
Joined: Sun Dec 12, 2021 4:38 am

122-16 and GnuRadio 3.10x

Post by math_pitaya » Fri Mar 03, 2023 5:48 pm

Are there any relatively straight forward ways to stream samples from a 122-16 device into Gnu-Radio(preferably 3.10x).

pavel
Posts: 789
Joined: Sat May 23, 2015 5:22 pm

Re: 122-16 and GnuRadio 3.10x

Post by pavel » Fri Mar 03, 2023 5:58 pm

Have you tried the application at the following link?

http://pavel-demin.github.io/red-pitaya ... er-122-88/

belotserm
Posts: 18
Joined: Tue Mar 07, 2023 8:49 pm

Re: 122-16 and GnuRadio 3.10x - goes through the motions but no TX or RX

Post by belotserm » Fri Mar 10, 2023 11:51 pm

I'm having the same objective, but no luck so far: have my new 122-16 SDRLab device, and followed these instructions exactly: http://pavel-demin.github.io/red-pitaya ... er-122-88/. Then in the trx_am.grc I replaced the source to be driven by an externally generated sine wave connected to the rx port 1 of the board and then to a frequency plot. No matter how I tried, the sine wave is not being received. Same problem on the transmit side: a sinewave generated digitally and then fed to a "red pitaya sink" is not showing up at the output - only some unrelated spurious components. Has anyone encountered this? The main reason I got this board is because I want it to be part of a staged SDR radio development, where parts of the processing will move to the board, and some will remain in GNU flowgraff. Can my board be defective? Perhaps it's missing some jumpers etc.? Any takers

User avatar
redpitaya
Site Admin
Posts: 881
Joined: Wed Mar 26, 2014 7:04 pm

Re: 122-16 and GnuRadio 3.10x

Post by redpitaya » Mon Mar 20, 2023 11:49 am

Are you using frequencies above 300 kHz? The SDRlab has AC coupling and will not receive frequencies below 300 kHz.

belotserm
Posts: 18
Joined: Tue Mar 07, 2023 8:49 pm

Re: 122-16 and GnuRadio 3.10x

Post by belotserm » Mon Mar 20, 2023 3:16 pm

Yes, I'm using 600kHz center frequency

belotserm
Posts: 18
Joined: Tue Mar 07, 2023 8:49 pm

Re: 122-16 and GnuRadio 3.10x

Post by belotserm » Mon Mar 20, 2023 5:57 pm

I can not get red_pitaya GR blocks to work. They run (no crashing or error messages), but no output. Is it possible the python version and/or GNU radio versions are newer than what this design supports? I'm on GNU Radio version 3.10.4, and Python is 3.10.6. Please advise

math_pitaya
Posts: 3
Joined: Sun Dec 12, 2021 4:38 am

Re: 122-16 and GnuRadio 3.10x

Post by math_pitaya » Tue Mar 21, 2023 5:19 am

I was able to get rx working(mostly) on osx in Ryan Volz's radio Conda Environment.
OSX 12
GNU 3.10.5
Python 10.8
I had a lot of trouble getting the path variables correct.
I haven't tested the sink block, but RX was fine when I launched gnu by opening the trx_AM.grc script.

Post Reply
jadalnie klasyczne ekskluzywne meble wypoczynkowe do salonu ekskluzywne meble tapicerowane ekskluzywne meble do sypialni ekskluzywne meble włoskie

Who is online

Users browsing this forum: pavel and 26 guests