Running Eco 2.22 and 2.23
-
- Posts: 115
- Joined: Fri Jan 09, 2015 6:07 pm
- Location: Babenhausen/Germany
Running Eco 2.22 and 2.23
Hello,
I don't know how to run one of the new Eco systems 2.22 or 2.23. Both don't show any reaction of booting, just the green LED is bright and the orange one dim. But nothing happens. Maybe it is a similar problem of recognizing the device.
With the old system 1.18 it is partly working -- with the common problems of connection interruptions.
Regards
Dieter
I don't know how to run one of the new Eco systems 2.22 or 2.23. Both don't show any reaction of booting, just the green LED is bright and the orange one dim. But nothing happens. Maybe it is a similar problem of recognizing the device.
With the old system 1.18 it is partly working -- with the common problems of connection interruptions.
Regards
Dieter
- redpitaya
- Site Admin
- Posts: 912
- Joined: Wed Mar 26, 2014 7:04 pm
Re: Running Eco 2.22 and 2.23
Please check this issue on GitHub. This is the most common problem for OS not working when upgrading from 1.04 to 2.00:
https://github.com/RedPitaya/RedPitaya/issues/250
https://github.com/RedPitaya/RedPitaya/issues/250
-
- Posts: 115
- Joined: Fri Jan 09, 2015 6:07 pm
- Location: Babenhausen/Germany
Re: Running Eco 2.22 and 2.23
Hello,
I already changed this entry to
STEM_125-14_v1.0
in May 2023. Do I have to change it once again?
Dieter
I already changed this entry to
STEM_125-14_v1.0
in May 2023. Do I have to change it once again?
Dieter
- redpitaya
- Site Admin
- Posts: 912
- Joined: Wed Mar 26, 2014 7:04 pm
Re: Running Eco 2.22 and 2.23
Try to refalsh the SD card image again to 2.00-23 and insert it into the Red Pitaya. If the hw_rev is correct, then there should be no problems. For the 2.00-23 OS you will need a 16 GB SD card (the OS takes around 8 GB).
Other than that I, do not see why there would be problems, besides plugging the power into the serial console uUSB port.
If this does not fix the issue, please send me a video of the attempted boot-up to support@redpitaya.com.
Other than that I, do not see why there would be problems, besides plugging the power into the serial console uUSB port.
If this does not fix the issue, please send me a video of the attempted boot-up to support@redpitaya.com.
-
- Posts: 115
- Joined: Fri Jan 09, 2015 6:07 pm
- Location: Babenhausen/Germany
Re: Running Eco 2.22 and 2.23
Hello RP,
I repeated to write the 2.23 image into a SD card. But this time with Win32diskimager, not with BalenaEtcher. This time everything seems to run, even the VNA starting, so that it is not necessary anymore, to change the card all the time. The calibration procedure I still have to do.
I can remember, that Balena reports an error message, but I don't remember, what kind of. But maybe this was the problem of not booting with this.
Best regards
Dieter
I repeated to write the 2.23 image into a SD card. But this time with Win32diskimager, not with BalenaEtcher. This time everything seems to run, even the VNA starting, so that it is not necessary anymore, to change the card all the time. The calibration procedure I still have to do.
I can remember, that Balena reports an error message, but I don't remember, what kind of. But maybe this was the problem of not booting with this.
Best regards
Dieter
-
- Posts: 110
- Joined: Tue Nov 16, 2021 11:38 am
Re: Running Eco 2.22 and 2.23
Hi Bulova,
I can report that while developing the latest versions of ecosystems I mostly used Ubuntu's default "Disks" utility (gnome-disk-utility) and it always flashed the SD card successfully. (if that information is of any use to you
)
I can report that while developing the latest versions of ecosystems I mostly used Ubuntu's default "Disks" utility (gnome-disk-utility) and it always flashed the SD card successfully. (if that information is of any use to you
![Smile :)](./images/smilies/icon_e_smile.gif)
-
- Posts: 115
- Joined: Fri Jan 09, 2015 6:07 pm
- Location: Babenhausen/Germany
Re: Running Eco 2.22 and 2.23
Hello,
I have to report, that there are some strange things that happened. With the 2.00-23 I still wanted to test the WiFi connection capability. But I was not able to get any connection with the WiFi dongle alone. (I copied my wpa_supplicant.conf to the SD root.) But in most cases the dongle did not illuminate its inner LED, and if it does, the RP was still hanging at the state where the red LED flashes. I even re-installed the same image again onto the SD, but nothing changed.
After this I put the card with the 1.04-18 back, and everything works okay, both with LAN and with WLAN. And there are all the new apps accessable, even Pavel's VNA works with connection and without changing the card.
I have no clue what happened. It seems that the plugging in of the WiFi dongle makes an effect, but there is no proove about it.
Best regards
Dieter
I have to report, that there are some strange things that happened. With the 2.00-23 I still wanted to test the WiFi connection capability. But I was not able to get any connection with the WiFi dongle alone. (I copied my wpa_supplicant.conf to the SD root.) But in most cases the dongle did not illuminate its inner LED, and if it does, the RP was still hanging at the state where the red LED flashes. I even re-installed the same image again onto the SD, but nothing changed.
After this I put the card with the 1.04-18 back, and everything works okay, both with LAN and with WLAN. And there are all the new apps accessable, even Pavel's VNA works with connection and without changing the card.
I have no clue what happened. It seems that the plugging in of the WiFi dongle makes an effect, but there is no proove about it.
Best regards
Dieter
- redpitaya
- Site Admin
- Posts: 912
- Joined: Wed Mar 26, 2014 7:04 pm
Re: Running Eco 2.22 and 2.23
Hello Dieter,
Thank you for reporting this. This was reported and the developers are working on it.
Thank you for reporting this. This was reported and the developers are working on it.
-
- Posts: 115
- Joined: Fri Jan 09, 2015 6:07 pm
- Location: Babenhausen/Germany
Re: Running Eco 2.22 and 2.23
Hello RP,
thank you. Does this mean, that it is a known bug? And with 2.00-30 is it solved already? Or where is it reported that this bug is solved? Is there any version log accessable?
In addition to my report: It is also the case, that not only the function with WiFi dongle is hanging, but the LAN cabled function as well (after the test with WiFi). The other OS with 1.04-18 works fine with all apps that I've been using like DFT spectrum analyzer, Bode analyzer, oscilloscope, oscilloscope and generator, and VNA.
Best regards
Dieter
thank you. Does this mean, that it is a known bug? And with 2.00-30 is it solved already? Or where is it reported that this bug is solved? Is there any version log accessable?
In addition to my report: It is also the case, that not only the function with WiFi dongle is hanging, but the LAN cabled function as well (after the test with WiFi). The other OS with 1.04-18 works fine with all apps that I've been using like DFT spectrum analyzer, Bode analyzer, oscilloscope, oscilloscope and generator, and VNA.
Best regards
Dieter
- redpitaya
- Site Admin
- Posts: 912
- Joined: Wed Mar 26, 2014 7:04 pm
Re: Running Eco 2.22 and 2.23
Hello Dieter,
Try to install Nightly Build version 2.00-232 or higher (the latest is 236). There were some bug fixes to Wi-fi applied there: https://downloads.redpitaya.com/downloa ... NGELOG.txt
https://downloads.redpitaya.com/downloa ... ly_builds/
Do not forget to install the latest 2.04 Linux: https://downloads.redpitaya.com/downloads/LinuxOS/
Try to install Nightly Build version 2.00-232 or higher (the latest is 236). There were some bug fixes to Wi-fi applied there: https://downloads.redpitaya.com/downloa ... NGELOG.txt
https://downloads.redpitaya.com/downloa ... ly_builds/
Do not forget to install the latest 2.04 Linux: https://downloads.redpitaya.com/downloads/LinuxOS/
jadalnie klasyczne ekskluzywne meble wypoczynkowe do salonu ekskluzywne meble tapicerowane ekskluzywne meble do sypialni ekskluzywne meble włoskie
Who is online
Users browsing this forum: No registered users and 106 guests